Somewhere in a commercial building, there is a run of gray steel pipe feeding a motor. No green wire runs inside it. It passed inspection. It has been fine for thirty years. And the only reason it has been fine is that a row of cheap steel couplings never worked loose.
That's the odd thing about conduit as a ground. The pipe doesn't announce that it's doing a safety job. It looks like a raceway, a place to put wires. But in a fault it becomes the most important conductor in the building, and nobody tests it.
The short answer
Yes. NEC 250.118 lists EMT, rigid, and IMC conduit as permitted equipment grounding conductors, and the EMT article itself (358.60) says so directly. In many commercial and industrial jobs, a separate ground wire inside the pipe is optional.
Notice the word permitted. The code isn't saying steel pipe is a perfect conductor. It's saying a properly assembled run of it is good enough to do one specific job.
The job: open the breaker, fast
The equipment grounding conductor doesn't exist to carry current in normal operation. It exists for the day a hot wire touches a metal enclosure.
Picture a frayed conductor touching the metal case of a motor. If nothing connects that case back to the panel, the case sits at line voltage. It waits for a person to touch it. That's the nightmare scenario.
Now give the case a low-impedance path home. The fault becomes a short circuit: hot wire, to the case, along the conduit, to the panel, back to the source. Current surges, the breaker's magnetic element trips, and the energized case goes dead in a fraction of a second.
NEC 250.4(A)(5) states the requirement plainly. The path must be permanent, continuous, and low enough in impedance to let enough current flow to open the overcurrent device. It also says the earth cannot be counted as that path.
That last point is the same idea behind the ground rod. Dirt is far too resistive to trip a breaker. Only metal back to the source will do.
Why steel pipe works
A breaker's instantaneous trip needs a large current. For round numbers, assume a 20-amp breaker wants somewhere around 100 to 200 amps to trip magnetically. The exact figure depends on the breaker.
Ohm's law then sets your budget. At 120 volts, 200 amps means the whole fault loop must come in under about 0.6 ohms. For 100 amps, about 1.2 ohms.
A length of EMT has a lot of steel in its wall, and steel is a fair conductor when there's plenty of it. The pipe's cross-section is comparable to or larger than a ground wire that could be sized for the circuit. For short and moderate runs, the pipe alone comes in under budget.
Steel has a quirk, though. Its resistance is much higher than copper's, and it's magnetic, which raises its impedance to AC. A fault current flowing in the pipe next to the hot conductors helps: because the go and return paths are bundled together, inductive effects partly cancel. This is one reason the code wants every conductor of a circuit in the same raceway.
So the pipe's wall is rarely the weak spot. The joints are.
Where the path actually breaks
A run of conduit is not one conductor. It's a chain of pieces held together by fittings, and each link is a place where resistance can creep in.
- Loose set screws. A set-screw coupling relies on a screw biting into the tube. If it was never tightened, or was tightened over a painted surface, the contact is a handshake with gloves on.
- Paint and rust. NEC 250.12 requires removing nonconductive coatings like paint or enamel where the connection needs to be electrically continuous. A wrapped coupling over a painted surface can look perfect and conduct poorly.
- Vibration. Pipe feeding a motor or compressor shakes. Fittings that were tight on day one can slowly back off.
- Corrosion. Outdoors and in damp locations, joints corrode. Corrosion adds resistance exactly where you can't see it.
- Damage. A pipe crushed by a forklift or a coupling pulled apart during a renovation leaves a gap downstream of the break. Everything beyond it stays energized in a fault.
Notice what these have in common. None of them affect the lights, the motor, or normal operation. The circuit works fine with a bad ground path. You only find out during a fault, when it matters.
The flex exception that trips people up
Flexible metal conduit (FMC) is where beginners get caught. Its spiral construction makes a high-impedance path, because the current has to follow the coil.
NEC 250.118 allows FMC as a ground path only under conditions: the length is 6 feet or less, the circuit is protected at 20 amps or less, and the fittings are listed for grounding. Beyond that, you need a wire inside it.
The same logic applies to flexible connections to vibrating equipment like a motor. Many electricians run a bonding wire in any flex, just to avoid the question. It's cheap insurance.
If you pull the wire anyway, there's also the case where the code requires it regardless: an installation with sensitive electronics, or any run through areas where you don't trust the pipe to stay intact. Some specs call for a wire-type ground in all conduit. Check the job spec before you assume the code minimum is the standard.
Your next moves
- Pull on every coupling and connector you can reach on your next EMT job. Grab it with a hand on each side and try to twist and separate the fitting. If anything moves, tighten or replace it before you close up.
- Scrape paint at connection points. Wherever a locknut, bushing, or set screw bites a painted box or panel, remove the finish down to bare metal so the contact is real.
- Count your flex. Measure each run of FMC. If it's over 6 feet, or the breaker is over 20 amps, or the fittings aren't marked for grounding, pull a green wire through.
- Use a continuity test, not just your eyes. With the power off, measure resistance from the far end of a conduit run back to the panel's ground bar. A good run reads very low, a fraction of an ohm. A high or open reading tells you a joint has failed.
- Decide on a wire for any run feeding vibrating or hard-to-inspect equipment. If a motor, a rooftop unit, or a buried or concealed run depends on pipe joints you can't see again, pulling the extra conductor costs minutes and buys a path you can verify.
The takeaway
Conduit as a ground is a bet on assembly quality. A well-made EMT run is a robust, permitted, low-impedance path. A sloppy one is a ground wire with invisible breaks in it, and neither version looks different from the outside.
That's why the number-crunching and the code citations matter alongside the craftsmanship. Voltage drop, fill, and ampacity all get checked on paper. The fault path rarely does, and it deserves the same attention.
Voltly keeps the ground sizing tables and the NEC references you'd want on a job like this in your pocket, offline, so you can check whether a run needs a wire without leaving the panel room. If that sounds useful, you can find it at https://voltly.lumenlabs.works.